In every household cleaning, the cleaning work of kitchen is the largest, and the lampblack machine is the most difficult to wash in the kitchen. By the end of the year, every household will start to clean the range hood, so how to clean it? For housewives, does a clean range hood make them feel better in an instant?
In fact, knowing the composition of each part of the range hood can make the cleaning work easier. The range hood mainly consists of air duct, fan, motor, check valve, oil collection and drainage device, lighting device, etc. the materials of each part are different, the division of labor is different, and there are different emphases and skills in cleaning. According to the structure of the range hood, I summed up a relatively convenient cleaning sequence and method of the range hood to facilitate your understanding. However, from a professional point of view, it is recommended not to dismantle the range hood without permission, but to ask a professional range hood cleaning home service.
Step 1: clean the internal machine of lampblack machine
As the saying goes, sweep the house without sweeping the edge, even one day. As for the cleaning of the lampblack machine, the motor, fan, impeller and other components are all the core power devices for the lampblack machine to exhaust the lampblack. Even if the exterior is polished, if the core devices are not clean and greasy, the use effect of the lampblack machine will be greatly reduced. In particular, the impeller, generally used for half a year or so, will be covered with oil stain. If it rotates with overload oil stain for a long time, it is not only easy to deform the impeller, increase the operating noise of the cigarette machine, affect the use effect, shorten the service life of the lampblack machine, but also have adverse effects on human health. Therefore, it is necessary to maintain regular cleaning.
Remove the impeller before washing. When removing the impeller, first screw down the impeller hand nut clockwise, and then remove the impeller with great care, handle it gently, so as to avoid deformation caused by excessive force. The cleaning of the internal machine is complex. It should be noted that the motor and circuit parts must not be watered during cleaning, otherwise it will lead to leakage, circuit short circuit and other situations; sharp, hard objects, steel wire balls and other instruments that damage the surface, as well as detergents with strong corrosiveness, strong alkali and strong acid are prohibited. Instead, use the micro wet cleaning cloth with special detergent to wipe the surface to remove the oil stain; when cleaning the impeller, use kitchen paper or cotton yarn head with strong oil absorption force to wipe one by one along the longitudinal direction of the blade from the axis outward, pay attention to the strength, so as not to cause the deformation of the impeller and affect the use. After the oil is removed, clean the impeller surface alternately with clean wet cloth and dry cloth, and then install it back to the original place, and it will be finished.
Step 2: clean the turbine, volute and fan blade of the range hood
There are two ways to clean the turbine, volute and fan blade of the range hood. Dismantling and cleaning method: after the corresponding parts are removed, use cleaning solvent (such as oil fume, detergent and vinegar mixture) to soak, wipe and other conventional cleaning, and then install the original way. The other is the high-pressure steam method without dismantling. The specific method is: first spray the detergent on the leaves and the inner wall to soften the oil stain; then put half of the cold water in the high-pressure boiler and heat it. When the steam is continuously discharged, take the lower limit pressure valve, align the steam water column with the rotating leaves, and start the range hood; At this time, the centrifugal force generated by the rotation of the machine will throw away the softened oil, and the sewage will flow into the waste oil box following the oil drain tank; finally, clean the inner wall of the fan blade, turbine and volute.
Step 3: oil fume oil box and oil net
After cleaning the leaves, there are a lot of old and new oil dirt in the oil fume oil box. At this time, first pour out the oil dirt in the oil box, and then soak the oil box in soapy water or warm water mixed with neutral detergent for about 15 minutes. If the oil dirt is stubborn, soak for 30 minutes. After long-term use, the lampblack machine has a thick layer of oil dirt on its oil net. If there is a small amount of oil dirt on the oil net, it can be washed and dried directly with warm water. If the oil dirt is serious, it can be soaked with the oil box. After soaking, rinse with water and wipe with a clean cloth.
In addition, it can also be applied with soap. Take a little soap with strong decontamination power and mix it with water to form a paste. Smear it on the oil screen, oil box and other parts that need to clean the oil stain. Wait for about ten minutes, and then wipe off the paste soap with a rag, and then you can easily wipe off the oil stain. In essence, whether the oil net is clean or not is related to the material and structure of the range hood. The oil net made of those iron wires is relatively rough and single, which is not only easy to get oil, but also not easy to clean. The mesh is easy to block and damage. The oil net with good quality has smooth surface, which is not stained with oil and easy to clean. For example, the Fangtai intelligent star magic lampblack cxw-358-z1t-m, which is developed by Fangtai innovation, has its unique long grid oil net, integrated panel, open space and simple plane structure, which controls the edge and corner gap to the minimum, and reduces the difficulty of cleaning and maintenance for users from the design level.
On the one hand, the long barrier acts as the smoke screen, covering 2 / 3 of the rising area of the oil fume. In addition to the oil fume inhaled from the oil fume machine, a small amount of oil fume condensed on the smoke screen will be very good for cleaning, and it can also play a preliminary role in oil fume separation; on the other hand, the oil screen surface is also attached with an oil resistant coating, which is easy to disassemble and clean. In addition, the volume of the oil box is very large, so the user does not need to clean it frequently.
For the convenience of cleaning in the future, after cleaning, sprinkle a thin layer of soap powder on the two oil storage tanks, and then inject about one third of the water, so that the recovered oil will float on the water surface, after pouring out, simply wash and then process like this; or put a small one-time oil box in the oil storage tank, and then take out the waste oil and throw it away.
Step 4: clean the fuselage, shell and hood of the range hood
Finally, clean the surface of the range hood. When cleaning, first use a cleaning cloth (the cleaning effect is better if you use a cloth soaked in hot water) dipped with a proper amount of neutral detergent for kitchen cleaning to wipe, and then use clean water to wash the residual liquid on each part, it will look fresh. If it is the material that is not easy to be contaminated with lampblack, it is easier and labor-saving to clean it. When choosing lampblack machine, consumers should choose the product with easy to clean material. Only by mastering the correct cleaning methods can we achieve twice the result with half the effort. Through the above description, do you have a clear understanding of how to clean the lampblack machine? Lampblack machine is one of the most dirty appliances in the kitchen. Only regular cleaning can keep the kitchen clean all the time, and the lampblack machine can also be used frequently.