In our life, many friends like to buy some flowers to decorate the house. With beautiful vases, it can be said to be a bright scenery, but do you know? Vase flower arrangement is also exquisite. So what are the precautions for vase flower arrangement? Now let's learn about it
What are the precautions for vase flower arrangement
1. Method of drying vase
Don't dry the vase with a rag. There are usually a lot of microorganisms on the rag. Therefore, the natural air drying method is the best.
2. How to prevent and remove vase dirt
Keeping the bottle water clean can prevent the formation of dirt. If water is used for bottle insertion, it can not control microorganisms and bacteria, and the use of cut flower preservative can prevent this situation. Using the right dose is the key to achieving the best results.
3. How to store the vase
After cleaning the vase, there will be small water droplets attached to the bottle wall. These water droplets are the best breeding ground for bacteria. Therefore, attention should be paid to inverting the cleaned vase in order to dry the water drops quickly and prevent dust from entering.
4. Clean the vase in time
During bottle insertion, microorganisms will breed in the bottle insertion solution. They are harmful not only to the bud, but also to the stem. Some flower stems will decompose and adhere to the inner wall of the vase (especially on the bottle wall at the water surface), which is difficult to clean. Therefore, after using the vase, it should be cleaned with detergent immediately.
5. Rinse again before use
If the vase is placed in the cabinet for a period of time, it will be contaminated with bacteria or dust, so it should be cleaned again before use, so as to make the vase fresh and clean.
The above introduces the relevant contents of the precautions for vase flower arrangement. Let's take a look at the skills of vase flower arrangement.
1. Group binding method: some wild grasses and flowers have gorgeous and moving colors, but the flowers are very small. One or two flowers can't reflect beauty, and good effects can only be revealed when they are concentrated. Therefore, when arranging flowers, you can hold the flowers into a ball, tie them with ropes or metal wires, and then insert them.
2. Flower arrangement reverse buckle method: when using woody flower arrangement, it is inevitable to encounter heavy flower branches and light flower sockets, resulting in lodging. At this time, a flower socket can be buckled on one side of the flower socket to increase the gravity.
3. Metal wire threading method: the center of the flower stalk of some flowers is empty, such as Calendula, celery and Fu Lang flower. You can choose a metal wire with moderate thickness and insert it from the incision or from the center of the stamen. This method will not affect the appearance of the flower branches and can make the flower branches bend freely, but it can not be used for non hollow flower branches, such as carnation, chrysanthemum, etc. In the process of metal wire threading, if it is difficult to wear the upper part of the flower branch and the Department near the flower, it should not completely penetrate the flower branch according to the details, or enough, or entangle the Department threading and department encircling.
4. Incision bending technique: the bending angle required for woody flower technique is not large. Scissors can also be used to cut the flower stem obliquely. The incision depth should not exceed 2 / 3 of the diameter of the flower stem, and then hold both sides of the incision with both hands and slowly bend the branches. If the toughness of the branch is strong, small wood chips can be embedded in the incision.
5. Flower socket connection method: the size of flower socket is limited. Sometimes in order to make large flower arrangement, it is not enough to rely on one flower socket alone. In order to arrange more flowers, you can put several flowers together and nail them horizontally with several twigs.
6. Metal wire encircling entanglement method: in order to support some flower branches and overcome the defects of flower morphology, the flowers can be spiral climbing and binding. The metal wire with enough hardness to make the branches bend around the entangled branches and bend according to their own ideas. However, the metal wire should not be too thick or affect the ornamental effect of flower arrangement. If necessary, the metal wire can be wrapped with a layer of green cotton paper or painted with green paint. In this way, the bending of flower branches can be changed freely and do whatever they want. This method is suitable for the treatment of soft flower branches.
7. Wedge inlay modeling method: for rough and hard woody flowers, in order to achieve the beauty of natural bending without exposing artificial traces, triangular wedge wood can be inlaid into the branch incision to be modeled. Wedge wood shall be made of the same plant material, and the thickness and size shall be basically the same. The flower school made in this way is soft and satisfactory. It is generally shameful and will not affect the absorption of water by the branches.
8. Leaf rolling method: there are some flowers, such as Indocalamus leaves, book belt grass, etc. the original shape can be changed by curling. The method is to take a leaf and flatten it, roll the leaf from the leaf tip to the leaf stem with a thin rod, and take out the thin rod for repeated kneading until you let go of your hand. The leaf still has a certain curl. If you want to be spiral, you can roll the blade obliquely, and it will be spiral after setting.