Sihai network

Summary of the latest test points deduction standard of subject 2 in 2018

Summary of the latest test points deduction standard of subject 2 in 2018

Sihai: the new regulations of driving test in 2017 were introduced. Many students make complaints about it.

Hang up directly. As the most important test subject, do you know the latest deduction standard of 2018 driving test new regulations? Let's take a look at this together and hope to help you avoid trouble in these areas.

1、 Test sequence

Starting from the uphill, stop at a fixed point, stop at a side direction, drive in a curve, turn at a right angle, and back into the warehouse.

2、 Analysis

Be careful, these places are easy to deduct points for comprehensive evaluation

100 points for failing to fasten the safety belt: 100 points for failing to close the door:

Turn signal not on: 10 points will be deducted if you do not use the turn signal before starting, turning, lane changing, overtaking, or parking, or if you use the turn signal for less than 3 seconds (use the turn signal for less than 3 seconds often becomes the reason for students to deduct points). )

One time of flameout: deduct 10 points

3、 Five test standards and skills

(1) Fixed point parking and ramp starting

1. Examination standard

Deduct 100 points if there is no fixed-point parking; deduct 100 points if the front bumper fails to reach the control line after the vehicle stops

Deduct 100 points if the rear sliding is more than 30cm after parking; deduct 10 points if the rear sliding is less than 30cm after parking (deduct 20 points if the original regulations)

Deduct 10 points if left turn signal is not turned on when starting

Deduct 100 points if the vehicle drives the solid line on the edge of medium voltage Road

If the front bumper fails to reach the parking line after the vehicle stops, 10 points shall be deducted (20 points shall be deducted according to the original regulations); if the front right track edge line is more than 30cm, 10 points shall be deducted (20 points shall be deducted according to the original regulations)

If the starting time is more than 30 seconds, 100 points will be deducted (new points will be deducted, which is the most exam item for students to fall into. )

2. Site requirements

The gradient of the steep slope must be greater than or equal to 10 degrees, and the length of the steep slope for C1 driving test must be greater than or equal to 20 meters. During the test, students must start within 30 seconds after stopping on a steep slope, otherwise they will be regarded as failures.

3. Operation skills

(1) After hearing the command of "stop at a certain point on the uphill" (turn on the right turning light immediately), lean towards the right side of the site; (if there is a slope when starting, in order to prevent sliding, use the half slope starting method).

(2) When arriving at the roadside, turn left for half a circle, and then turn right quickly to make the right side of the vehicle parallel to the roadside, and the distance is within 30cm (keep the connecting part (Black Square) in the middle of the left wiper between the white line and the yellow line, do not press the yellow line; it is better to press the white dotted line, or use the left reinforcement line to align with the sign line); after starting, fully release the clutch( Or use clutch control, the speed is faster, and it is not easy to turn off) to go uphill (in the uphill process). If the car shakes obviously, you can step on clutch a little and keep it on).

(3) When arriving at the stop, step on the clutch to slow down the speed. When you see the stop mark to the right, step on the foot brake, step on the clutch to stop (or you can see the edge of the positioning pile line from the bottom of the left reflector), pull the hand brake, (turn off the steering light), take off the neutral gear and lift the clutch (you must lift off the clutch before starting).

(4) Stop for 10 seconds, wait for the results to be reported, prepare for half slope starting, step on clutch, (step on foot brake), shift to gear 1, (turn on the left turn light, and press the horn once); release the hand brake; (new regulation: if the left turn light is not turned on when starting, 10 points will be deducted)

(5) Slowly lift the clutch. When the car body feels shaking or makes a sound of gear running in, lift the foot brake (fully release) and (lightly step on the accelerator), and the car will move forward. (for the method of not turning off the engine, release the brake when the vehicle shakes. If the vehicle does not go idling and drops rapidly, timely step on the clutch and foot brake, keep the engine on, not slip, and then start again) (Note: if the starting time is more than 30 seconds, deduct 100 points, add new items with points deducted, and the most exam items for students to fall off. )

(2) Side parking

1. Examination standard

Deduct 100 points for outgoing line of vehicle body after vehicle warehousing stops

Deduct 10 points if the wheels touch the lane boundary during driving

Deduct 100 points if not parked in the garage

Deduct 10 points if left turn signal is not turned on when starting

10 points will be deducted if the right turn signal is not turned on when reversing (additional points will be deducted. Previously, only the left turn signal is required to be turned on when parking and starting, which is also the most easily ignored item leading to points deduction. )

Deduct 100 points if you stop halfway

2. Site requirements

Side parking is often encountered when driving. After the implementation of the new regulations, there is no longer a bamboo pole for side parking, and the garage boundary is made in the form of lines drawn on the ground. For students studying C1 driver's license, the length of the parking space on the side is 1.5 times the length of the vehicle plus 1 meter. As long as the parking space is in the inner side of this range and the parking space does not cross the line, it is considered to pass. Pay attention to the new regulations: deduct 100 points if you stop halfway;

3. Operation skills: speed must be controlled at about 5km

(1) The seat and rearview mirror shall be adjusted in advance (the rearview mirror shall be adjusted in this way: the left rearview mirror, the upper and lower positions are to center the horizon in the distance, and the left and right positions shall be adjusted to make the vehicle body occupy one quarter of the mirror area; the right rearview mirror, when adjusting the upper and lower positions, shall have a larger ground area, accounting for about two-thirds of the mirror surface, and the left and right positions shall also be adjusted to the vehicle body occupy Just a quarter).

(2) After hearing the side parking instruction, the semi linkage driving shall move slowly and parallel along the parking space (first 1 / 2 on the right side of the car, and then gradually 1 / 3 of the garage side line, i.e. keep the right side of the car 750px away from the garage side line). When the front side line of the garage is seen in the right rear-view mirror, step on the foot brake, step on the clutch to stop;

(3) Step on the clutch and engage the reverse gear (new regulation: turn on the right steering light for more than 3 seconds), raise the foot brake and slowly lift the clutch to reverse; (at this time, if the front of the car is inclined, when reversing, you can beat the side with the direction deviated from the front of the car, and immediately return the steering wheel to the normal when the car body is back to the normal);

(4) When the front edge line of the warehouse just can't be seen in the right rear-view mirror, continue to reverse in the right direction;

(5) Observe that when the car body is at an angle of 40-45 degrees with the left line of the garage, the direction will return to the left (1 and a half circles) (or when the right rear corner of the garage just appears at the rear of the car in the left rearview mirror, the direction will return to the left by 1 and a half circles);

(6) After returning to the wheel, continue to reverse slowly. Look at the left rear-view mirror. When the left rear wheel reaches 250px in front of the left line of the warehouse, continue to beat the direction to the left;

be careful:

1. When the starting vehicle and the warehouse boundary line are greater than 1000px, step 5 or step 6 shall be turned late.

2. When the starting vehicle and warehouse boundary line are less than 500px, step 5 or step 6 should be oriented early.

(7) Observe the right rear-view mirror. When the car is back to the normal position and the steering wheel is back to the normal position. When the car is not in place, continue to back down (make the rear wheel enter the sensing area but not out of the rear sensing area), step on the foot brake, step on the clutch parking, pull the hand brake, take off the neutral gear, then lift the clutch, lift the foot brake, stop for about 10 seconds, and prepare to start again after passing the general knowledge test;

(8) Step on the clutch, shift to gear 1, turn on the left turn light for more than 3 seconds, press the horn, release the hand brake and slowly lift the clutch with semi linkage to start slowly; the direction is left to kill;

(9) Drive along the left side. When the front of the car presses the left line of the road in the middle, make one and a half circles to the right as soon as possible (back to normal), then make another circle to the right according to the road conditions, and adjust appropriately;

(10) After the vehicle body is parallel to the boundary line of the warehouse, immediately turn the steering wheel back to the right (i.e. turn left for one circle, how many rounds); continue to move forward and drive away from the test area of this project.

(3) Curve driving

1. Examination standard

Deduct 100 points if any wheel presses the edge line of the road (deduct 20 points if the wheel presses the edge line originally specified, and deduct 100 points if it crosses the line). The new standard extrusion sideline was also increased to 100 points. )

Deduct 100 points if you stop halfway

2. site requirements

The curved driving field looks like a letter s lying on the ground. According to the standard for dimensions of small car test items, the arc radius of C1 driving curve driving site is 7.5m. When the vehicle needs to enter from one end of the s-lane, it will leave from the other end without pressing the line.

3. Operation skills

Curve driving

(1) When the vehicle enters the first curve (visual inspection), keep 0.5m from the left side of the vehicle and the left line into the curve (or the left front corner of the vehicle enters in the middle of the road), use the left car head to press the right line to draw an arc, keep the constant speed and low speed, and correct the direction properly;

(2) When the vehicle turns from the first corner to the second, the left car head leaves the right line, and the right car head gradually enters the road from the right side. When the right car head goes to the middle of the road, turn right;

(3) When entering the second bend (visual inspection), use the right headstock to press the left line to draw an arc and correct the direction properly;

(4) When going out of the curve, turn the direction and enter the straight line.

Pay attention to the new regulations: deduct 100 points if you stop halfway

(4) Right angle turn

1. Examination standard

Deduct 100 points if any wheel presses the edge line of the road (deduct 20 points if the wheel presses the edge line originally specified, and deduct 100 points if it crosses the line). The new standard extrusion sideline also increased to 100 points. )

Deduct 100 points if you stop halfway

2. Site requirements

The right angle turning field looks like an L on the ground. After the implementation of the new regulations, the length of the right angle turning site shall be no less than 1.5 times the vehicle length, and the road width shall be the wheelbase of small vehicles plus 1 m.

3. Operation skills

Right angle turn

Before entering a right angle turn, make the vehicle move forward and slowly on one side of the sign pole at both sides of the road as far as possible away from the turning point (press the outer edge line at 1 / 3 of the head of the vehicle, align the left rib of the head with the mark point); when the rear-view mirror at the side near the turning point coincides with the turning point, hit the direction at the side of the turning point and return to the right direction through the rear-end timing.

Pay attention to the new regulations: deduct 100 points if you stop halfway

(5) Reverse storage

Reverse storage

A. Right outbound line: when the front of the car coincides with the 6m line, turn right for 1.5 circle, turn left for 1.5 circle at the timing, and walk forward for 50cm or 1m to stop.

B. Right stick to the garage: put the reverse gear on, turn the car to the right full or circle, look at the right mirror to find the end point of the test line in the garage, turn around the end point on the solid line, keep the car and the end point on the solid line at 10-15cm and turn to the right full, then look at the left mirror to show the rear corner of the solid line at 10cm, walk while returning to the right for 1.5 circle, look at the overlap of the handrail or lock core of the left front door and the rear horizontal solid line of the garage, and then stop.

C. Left outbound line: the front of the car coincides with the 6m line, and the car is fully turned to the left or 1.5 circle, the timing of the car is turned back to the right for 1.5 circle, and the car stops 50 cm or 1 meter forward.

D. Left reverse storage: when the car is turning full or 1.0 circle to the left, look at the end point on the left solid line around the left mirror, keep the car and the end point on the solid line at 10-15cm and turn full to the left, then look at the right mirror to show the right rear solid line corner, walk back and look at the overlap of the handrail on the left front door and the rear horizontal solid line, then the car can be divided into middle and parking.

1. Examination standard

Deduct 100 points for driving not in accordance with the specified route sequence

Deduct 100 points if not completely poured into the warehouse

Deduct 100 points for outgoing line of vehicle body

Deduct 100 points for parking in the middle of the way (the former examination students can stop before entering the warehouse. Now, once the GPS positioning determines that the vehicle is in the state of complete stop, the students will be directly deducted 100 points. )

2. Site requirements

Most of the bamboo poles that used to stand in the mid air have been taken down in the new site. Single warehouse is used for reversing. After the implementation of the new regulations, the pile test and field test were combined, and the small car pile test was changed to reverse storage, and the transfer between two pile positions was cancelled. Reverse storage, students can't stop in the middle of the test, once stopped, the test is not passed.

3. Operation skills

(1) Step on clutch, step on brake; shift to reverse gear, (new regulation: turn on right turn light), release hand brake; release foot brake;

(2) Slowly release the clutch to back up; look back at the right rear, align the middle column (black edge) of the right rear window with the right corner of the garage, and immediately hit the right direction at a uniform speed; see the whole left line just appeared in the left rear-view mirror, and immediately straighten the steering wheel. Observe the rear-view mirrors on both sides, straighten the body; stop when the left door handle (blue dot mark) is level with the garage bottom line.

(3) Change gear and drive forward. When the hood is close to the white line (7m line) and almost touches the white line, turn the steering wheel to the left at a uniform speed,