In the decoration, floor tile is a very important process. How to choose floor tile? What is the importance of floor tile not absorbing water? How to remove the floor tile film? Let's have a look.
Floor tiles are good or bad if they don't absorb water
Some families react that their tiles don't absorb water. Back up the tiles to do the water absorption experiment. The water sprinkled on them is like a lotus leaf. They are in the shape of a ball and do not absorb water at all. How about this kind of floor tiles? Here are some pertinent answers to this question:
First of all, we need to make it clear that the ceramic tiles are made of high-temperature juice, with some small holes. The lower the water absorption of ceramic tile indicates that the higher the density of ceramic tile, the less the pores in the ceramic tile, and the higher the hardness. In short, the lower the water absorption, the better the quality. Then I'll give you some suggestions.
1. From the point of view of satisfying users, different water absorption tiles meet different use sites. So do not blindly pursue low water absorption ceramic tile.
2. All ceramic tiles, that is, non absorbent ceramic tiles, can fully meet the use requirements of the wall and floor in the family decoration. As a family decoration, they are mainly used for the floor decoration. In the home decoration, if the construction workers have poor skills, it is easy to cause falling off and other safety accidents in the later stage, it is generally not recommended for wall decoration.
3. From the point of view of meeting the use, ceramic glazed tiles can meet the use requirements, and the national water absorption standard is between 9% - 20%.
4. Ceramic tiles with water absorption of more than 9% are commonly known as ceramic tiles. This kind of ceramic tile has relatively high water absorption. When cement mortar is used for paving, it needs to be treated by water soaking (the purpose of water soaking is to prevent the water absorbing ceramic tiles from absorbing the water in the cement mortar too quickly after plastering the cement mortar without water soaking, so as to shorten the setting period of the cement mortar and cause the ceramic tiles to stick The knot is not firm.
5. There is no direct relationship between the permeability of ceramic tile and the quality of ceramic tile. (water permeability refers to whether the water is watermarked on the front after pouring water on the back of the tile).
What to do if the floor tiles at home don't absorb water
Since laid the tile that does not wash water very much, that also should pay attention to these matters in the ordinary daily cleaning and maintenance, lest the home is wet.
1. Usually, when mopping the floor, try to use the mop of pure cotton or bamboo fiber to dry and then mop the floor, generally there will be no water drop.
2. Don't open the window in rainy days, lest the raindrops come in and wet the ground, which is hard to dry.
3, when choosing cleaning agents, foam less detergents should be chosen, so that there is no need to spend a lot of time and water to clean the foam.
How to remove the floor tile film
Wet the floor tile with the watering pot
Wet the floor tile surface with a watering can and leave for a few minutes. Then use a shovel to gently remove the corner of the floor tile film, and lift it by hand. If the film is close to the floor tile surface, you need to prepare some water, and then use a shovel to slowly shovel away. If the decoration process, more dust, film and floor tiles will fit more tightly.
Steel wire ball wiped off
If the film of floor tile is made of plastic, you can tear it slowly by hand from the corner, or scrub it with steel wire ball, but you can't scrub it too hard to avoid damaging the ground and affecting the appearance.
Warm water + detergent
To remove the membrane of floor tile, warm water can be used, and a proper amount of detergent can be placed, and evenly applied on the brick surface. Wet while tearing, especially the complete film, good to remove. If part of the film needs to be treated, the detergent can be put on the film, and then the blade can be used to gently remove it.
Acidic liquid
When the ceramic tile protective film can't be torn off, we can use the acidic liquid such as dilute hydrochloric acid and jiechuanling, but we must pay attention that the concentration can't be too high. We can dilute it a little, and then apply it on the ceramic tile oxidation protective film. When the reaction happens a little later, we can remove it gently with a shovel, but we should pay attention to the liquid The body can't get on the floor tile.
Hair dryer removal
First, blow the floor tile film with an electric blower to a certain degree of heat, and then wash it with cold water. Due to the effect of thermal expansion and cold shrinkage, the film on the brick surface will expand in different sizes, so the film is relatively easy to remove, and the effect is good.
Banana water wipe
If the area of the film on the ceramic tile is small, we can also use banana water to wipe it, and then use the steel wire ball to rub it off.
How to remove different protective films
1. If the protective film on the surface of the ceramic tile is plastic film, this is simple. We only need to tear it by hand gradually, and then use the steel wire ball to gently wipe the ceramic tile, or use the electric hair dryer to heat it and make the protective film blister, which is also easy to tear off.
2. If the protective film on the surface of the ceramic tile is antifouling agent protective film, we can use a towel dipped in white cement to clean the protective film.
3. If the surface of the ceramic tile is ceramic tile wax protective film, we can use dry towel to scrub, banana water to scrub, and talcum white cement to scrub.